Supersprint Manifold, Sport Cats and Exhaust

[imran]

I ordered this as soon as the car arrived. Looking forward to getting it on and releasing the V8 sound.

I will report back with sound clips and dyno data.

[macfly]

That looks beautifully made, are you going to do a marine ceramic coating before installing it?

[beamon]

Looks awesome. I am looking forward to your install and results. I ordered the Supersprint manifold last month...waiting for it to arrive. Also ordered the pipes that delete the center resonators. I am going to use the factory cats and existing Eisenmann rear exhaust on the car.

Is the marine ceramic coating recommended to minimize heat buildup?

[macfly]

Is the marine ceramic coating recommended to minimize heat buildup?

Yes, plus it looks great and it protects the metal.

[imran]

That looks beautifully made, are you going to do a marine ceramic coating before installing it?

No plans to do this (and exhaust is already on the car). Its not something I've ever seen the benefit of proven especially considering the cost.

[imran]

It sounds amazing. Looking forward to sharing proper video clips with you all next week.

I have some clips on my instagram if you want to check it our briefly @_imran_arshad

[imran]

Video is up. Enjoy!

[DakotaGT]

Video is up. Enjoy!

https://youtu.be/iH8HoOC3BeU

Wow, incredible video, and that system sounds amazing! If I lived in the UK, my car would be headed to your shop immediately.

[MauiMike]

Thanks imran - fantastic video. If my car was in the UK I’d be right over!

[Musta10000]

Imran - that’s phenomenal. WOW!

[beamon]

Fantastic video...really enjoyed watching the install and dyno results. I think you are doing a great service to the Z8 platform by showing how these mods can really transform the car, even 20 years later, and changing its personality from boulevard cruiser to true M car. I'm still waiting for my Supersprint headers to arrive and will be in touch for the ECU tune once installed. Also hoping that an air intake system is still being developed by you all!

[imran]

Thanks for the feedback guys. It really does sound incredible. Although this was done purely for sound the power gain is very noticeable. I haven't talked about the Bilstein MDS suspension much but I had a very good drive over this weekend and it has vastly improved the handling dynamics of the car. Really please with the way it has turned out.

Eventuri will also be developing an intake and carbon plenum cover for it. I will share details when I can. Lets see if we can get a nice induction roar too!

[CobraR1339]

Any chance these will not set off a CEL or code for cats. I am in California, perfromance cats have been dicey. I would love to try this set up. But nervous I have to swap it out every 2 years. No one is really looking for EOD#s, but codes can be an issue. My C5 vette system never tossed a code and was not a problem. My C6 system, same mfg, would throw warm up codes, not ready stuff, it would not pass emissions.

[Norcal]

Amazing! Thanks for the great video.

[GaZ8fan]

My Supersprint headers and catback exhaust are supposed to arrive in January. Four month lead time, can’t wait. Looking forward to the Eventuri intake development by Imran too.

[TheJQ]

My Supersprint headers and catback exhaust are supposed to arrive in April. Put me down for that Eventuri intake as well, Imran.

[GaZ8fan]

As reference I ordered the Supersprint headers and catback exhaust Aug 30 and am still waiting. Supposed to have shipped last week and the new shipping date has already been changed twice. The problem is the high flow cats. So don’t be surprised if it takes longer…

[2112]

Seems everything is taking forever.

[GaZ8fan]

Shipping date for the Supersprint high flow cats has been delayed again until the end of February. So at best it will be six months from the order date, two months longer than initial estimate. Really annoying. I’m going to go ahead and install the headers and exhaust next week with the stock cats for the time being.

[Peter Koh]

Hi Imran.
Thank you for the video, super work!!.
I have installed my Supersprint exhaust system without header (not available in RHD configuraion) on my Alpina Z8 (RHD)
Installed the following
Front pipes R+L with metallic catalytic converter
Centre pipe kit R + L (enhance the sound and reduce the back pressure)
Rear exhausts 90 L & R.

So happy with the installation and it sounded so good.
My only problem is that the " Service Engine Light" is lighted on my tacho after the installation and we have checked everything on the exhaust piping for leaks, especially in the area of the catalytics
I have reset the error codes but after 50km+ of driving, error appears again. I was told due to high flow cat, post O2 sensors may not be reading correctly and perhaps would need ECU -Remapping and tuning?
Not sure whether you could point me the right direction.
Thank you. Cheers Peter

[beamon]

Hi Peter, any drone with exhaust using the "Centre pipe kit R + L (enhance the sound and reduce the back pressure)" ? I have these pipes ready to install in the spring and was curious. Thanks!

[Peter Koh]

Hi Peter, any drone with exhaust using the "Centre pipe kit R + L (enhance the sound and reduce the back pressure)" ? I have these pipes ready to install in the spring and was curious. Thanks!

There are 2 oxygen sensors before the catalytic converter, handle it with care when removed and do not drop it.
Cutting and fitting should be a straight forward replacement work ... just make sure all the pipes are fully aligned before welding up the connecting joints and it should be fully sealed and no leak.
Hope this helps and good luck.

[GaZ8fan]

My high flow cats finally shipped today after a 6 month wait. Will get on my shop’s schedule in the next couple of weeks for the install of the headers, high flow cats and catback exhaust. I’m also having the primary O2 sensors replaced given the age and mileage. Then the dyno tune to maximize the hp gains and eliminate the possibility of a CEL from the high flow cats. Can’t wait!

[DakotaGT]

My high flow cats finally shipped today after a 6 month wait. Will get on my shop’s schedule in the next couple of weeks for the install of the headers, high flow cats and catback exhaust. I’m also having the primary O2 sensors replaced given the age and mileage. Then the dyno tune to maximize the hp gains and eliminate the possibility of a CEL from the high flow cats. Can’t wait!

Sweet! Looking forward to your results.

[Peter Koh]

Great and can't wait to see how you go with O2 sensors and dyno tune. Keep us posted. Cheers and good luck.

[TheJQ]

What's the part number on those primary O2 sensors?

[Peter Koh]

Here are the Pre O2 and Post O2 sensors part number both of these sensors you could get it from www.TurnerMotorsport.com

OEM Bosch Oxygen Sensor - mounts before catalytic converter - E46 E39 E38 X3 X5 Z3 Z4, Z8, Z8 Alpina
T#: 2998 Part: 11781742050
Genuine BMW Oxygen Sensor - E31 E52
T#: 37658 Part: 11781742052
Hope this helps. Cheers PK

[TheJQ]

Thanks very much, Peter.

[AlpinaOkie]

Too bad these won't fit an Alpina engine. Sounds great!